Home > Products > Hot-Dip 55% Al-Zn Coated Steel Coil
Brief of Product
Hot-Dip 55% Al-Zn Coated Steel Coil is made with Hot/Cold Rolled Steel Coil dipped into a molten tank filled with 55% Aluminum, 43.4% Zinc and 1.6% Silicate to form a barrier on steel coil and gain the characteristics of corrosion resistance.
Product Features
55% Al-Zn Coated Product gains corrosion resistance from the barrier protecting function of Aluminum and the sacrificing protecting function of Zinc. When Zinc is acting its sacrificing protection at cutting edge, scratch and bruise of coating layer, Aluminum will form an insoluble oxide layer and demonstrate its barrier protection function.
Applications
- Building Material
Floor deck, Ceiling, Conduit, Ventilating pile, Balcony, Warehouse, Roof, partition, Bean, Steel frame, Wiring panel, Wall, Sun-Shield canopy, Gutter, Window frame, Scaffolding , Air-Duct work, Underground channel and steel rolling door. - Electric Appliance
Stove, Washing machine, Refrigerator, Electrical junction box, Motor cap, Dehumidifier, Roaster, Illumination device, Fluorescent lamp, Freezer, Air regulator, Video machine, Heater, Microwave shell. - Transportation Industry
Interior panel of vehicle, Rear seat panel of bus and truck, Transportation system, Oil tank, Road sign, Road rail, Cargo container, Air purifier, Acoustic barrier. - Agricultural Equipment
Large barn, Agricultural dryer, Water tank, Irrigation channel, Hoarding house, Greenhouse, Silo, Stable, Feeder, Hopper container, Agricultural equipment. - Furniture & Others
Automatic vending machine, Funnel, Office equipment, Amusement equipment, Solar energy collector, Garage, Tool-Kit box, Steel furniture, Bucket, Interior equipment of sauna, Can.
Type symbols and mechanical property of Hot-Dip 55% Al-Zn coated steel
| Type Symbol of Hot-Dip 55% Al-Zn Coated Steel JIS G3321 |
Min. Yield Point N/mm2 | Min. Tensile Strength N/mm2 | Min. Elongation % | Uses | ||||
| Nominal Thickness mm (t) | ||||||||
cold rolled base steel |
0.25≤ t<0.4 |
0.4≤ t<0.6 |
0.6≤ t<1.0 |
1.0≤ t<1.6 |
1.6≤ t<2.3 |
|||
| SGLCC | 205 | 270 | 20 | 21 | 24 | 24 | 25 | Commercial |
| SGLCD | --- | 270 | --- | 27 | 31 | 32 | 33 | Drawing |
| SGLC400 | 295 | 400 | 16 | 17 | 18 | 18 | 18 | Structural |
| SGLC440 | 335 | 440 | 14 | 15 | 16 | 18 | 18 | Structural |
| SGLC490 | 365 | 490 | 12 | 13 | 14 | 16 | 16 | Structural |
| SGLC570 | 560 | 570 | --- | --- | --- | --- | --- | Structural |
| ASTM Designation | Min. Yield Point ksi(MPa) | Min. Tensile Strength ksi(MPa) | Min. Elongation% | Uses |
| A792(M) CS TYPE A,B,C | --- | --- | --- | Commercial |
| A792(M) FS | --- | --- | --- | Forming |
| A792(M) DS | --- | --- | --- | Drawing |
| A792(M) SS Grade33(230) | 33(230) | 45(310) | 20 | Structural |
| A792(M) SS Grade37(255) | 37(255) | 52(360) | 18 | Structural |
| A792(M) SS Grade40(275) | 40(275) | 55(380) | 16 | Structural |
| A792(M) SS Grade 50(340) | 50(340) | 65(450) | 12 | Structural |
| A792(M) SS Grade 60(410) |
60(410) | 70(480) | Thickness≦71mm, EL≧8﹪ Thickness＞71mm, EL≧10﹪ |
Structural |
| A792(M) SS Grade80(550) | 80(550) | 82(570) | --- | Structural |
Indicates in Metric System
Type symbols table of hot dip 55% Al-Zn Coated Steel
| Spec. | JIS | CNS | ASTM |
| Type | GL | GL | GL |
| Specification | SGLC | SGLCC | ASTM(M) CS Type A |
| ASTM(M) CS Type B | |||
| ASTM(M) CS Type C | |||
| ASTM(M) FS | |||
| SGLCD | SGLCD | ASTM(M) DS | |
| ASTM(M) SS Grade 33 (230) | |||
| SGLC340 | SGLC340 | ASTM(M) SS Grade 37 (255) | |
| ASTM(M) SS Grade 40 (275) | |||
| SGLC400 | SGLC400 | ||
| SGLC440 | SGLC440 | ASTM(M) SS Grade 50 (340) | |
| SGLC490 | SGLC490 | ||
| SGLC490M | ASTM(M)SS Grade 60 (410) | ||
| SGLC540 | ` | ||
| SGLC540M | ASTM(M) SSGrade 70 (480) | ||
| SGLC570 | SGLC570 | ASTM(M) SSGrade 80 (550) |
